1 Channel 5V Relay Module Time Delay Relay Module Trigger OFF / ON Switch

Relay module, delay off, off, trigger delay, cycle timing circuit switching

0.1 seconds (min) to 999 minutes (max) continuously adjustable .

This product is easy to use, many functions, but all buyers need to carefully read the instructions, very useful product.

Highlights:

1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;

2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;

3. The emergency stop function (“STOP” key);With reverse polarity protection, reverse polarity will not burn the product.

4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;

5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;

6. After the module is powered down, all parameter settings are not lost.

7.Weight：29g

Operating mode:

P1: trigger signal, the relay is on"OP" time, and then disconnect; in the "OP" time, as follows:

P1.1: signal is triggered again, invalid

P1.2: signal is triggered again, the clock is reset

P1.3: Signal trigger again, relay off, stop the clock;

P-2: trigger signal, the relay off "CL" of time, the relay on"OP" time, and then disconnect relay;

P3.1: trigger signal, the relay is turned on after the "OP" time, the relay off "CL" time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( "LOP ") can be set.

P3.2: without triggering signal, the relay is on"OP" time, the relay off "CL" time, and has been cycling; frequency ( "LOP") cycle can be set;

P-4: signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing "OP" time, the relay is; if another signal during timing, timing is cleared;

Product parameters:

1: Operating voltage: 6--30V, support microUSB 5.0V power supply

2: Trigger Source: Active-high (3.0V-24V), have optocoupler isolation, can improve the system's anti-jamming capability (customers can also shorting common ground).

3: Output capability: You can control the DC 30VDC 5A or 220VAC 5A device.

4: Quiescent Current: 20mA; Operating Current: 50mA

5: Life: more than 10 million times; Working temperature: -40-85 ℃; Size:6.2*3.8*1.7cm.

6: With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.

Special Note: The relay outputs are paive contact, justaswitch.

Timing range

0.1 seconds (min) to 999 minutes (max) continuously adjustable

How to choose the time range ?

After setting the mode selection screen parameter value by a short pre "STOP" on to select the time range;

XXX. decimal point in the unit place, time range: 1 second to 999 seconds.

XX. X decimal point in decade place, Timing range: 0.1 seconds to 99.9 seconds

X. X. X. decimal full brightne, Timing range: 1 minute to 999 minutes.

For example, you want to set "OP" is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2

Parameter description: "OP" - conduction time, "CL" - off time, "LOP" - the number of cycles (1-999 times, "---" represents infinite loop).

These parameters are independent of each other, but is shared by each mode.For example, in P1.1 mode, set the on-time "OP" is 5 seconds, if you switch to P1.2 mode, it's "OP" will be 5 secondstoo.

In the main interface (display 000), short pre "SET" on will display "OP" ( "CL", "LOP") and the corresponding time XXX;

Some parameters only mode "OP" (such as the mode P1.1, P1.2, P1.3), short pre the "SET" key to display only the “OP” and the corresponding time;

Some models have parameters "OP", "CL", "LOP" (such as the mode P3.1, P3.2), short pre "SET" on will display "OP" and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;

In the main interface by short pre "SET" key to see information about the parameters of the current mode, very convenient!

How to set parameters ?

1. First, read the instructions to determine the required operating mode.

2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; pre "SET" on for 2 seconds after release to enter mode selection interface; a short time by preing "UP", "DOWN" key to select the mode (P1.1 ~ P-4).

3. Select the mode (such as P3.2), short pre the "SET" on, then the parameter to be set flashes ( "OP" on-time, "CL" off time, "LOP" cycles ( "---" represents infinite loop)), by "UP", "DOWN" keys to adjust the parameter value, support long pre (rapid increase or decrease) and short pre (increase or decrease one unit); then short pre the "STOP" key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short pre the "SET" on to set the parameters of the current mode of procedure is as above.

4. After the parameters are set, long pre "SET" on for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of succe!

The main interface: I n the relay does not work status display "000" (no decimal point), with a decimal point under relay state.

Mode selection screen: Long pre the "SET" key to enter, after setting is completed, long pre the "SET" key to exit back to the main screen.

"STOP" on extensions:

Relays enable mode:

1. ON: Relay allows conduction in the "OP" on-time;

2. OFF: relay prohibit conduction is always closed;

In the main interface, short pre the "STOP" on to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)

Sleep mode:

1. "C-P" Sleep mode: five minutes without any operation, the digital display automatically turns off, the program running as usual;

2. "O-d" normal mode: digital display always open;

Pre the "STOP" on for two seconds and then release to switch "C-P" and "O-d" state, in which the current state of flashes and then return to the main screen.

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.