433Mhz RF Remote Control Switch AC 220V 30A On

433Mhz RF Remote Control Switch AC 220V 30A On Off Remote Controller Transmitter for Water Pump Motor LED Electric Appliance

• I am an international seller

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.433Mhz RF Remote Control Switch AC 220V 30A On Off Remote Controller Transmitter for Water Pump Motor LED Electric Appliance

Specifications:

Remote control Transmitter

Operating voltage: DC12V (23A/12V battery x1)

Transmitting frequency: 433MHz

Ening Type: Fixed e

Receiver sensitivity: > -105dB

Transmission distance : 100M (Open field)

Size: approx 55*28*10mm




Receiver board

Operating voltage: AC 110V - 240V

Output voltage = Operating voltage

Operating frequency: 433MHz(Same with Remote control)

Ening Type: learning e(you can buy extra 315MHz remote controllers for this receiver)

Rated contact current of relay: 15A/240VAC, 15A/110VAC (Please notice that : Although the relay is marked 30A 240VAC. The 30A is for the peak current of your load. The rated current of your load should less than 15A)

Box size: approx 65 x 45 x 28mm




Instructions:

1. Jog: The remote control is controlled by a on. After pressing the on, the relay is closed, and when the on is released, the relay is disconnected.

2. Self-locking: The remote control is controlled by a on. Press the on once to pull in the relay, and press it again to disconnect.

3. Interlock: The remote control is controlled by two ons. Press the A on to close the relay, and press the B on to disconnect.

4. Delay: After the pairing is successful, the relay will automatically disconnect after 5 seconds/10 seconds/15 seconds/20 seconds.




Learn to e:

1. Jog learning method:

Press the learning on of the controller once, the indicator light flashes quickly and it is in the learning state, and then press any on of the remote control you want to learn to send a e. At this time, the indicator light flashes three times and goes out, and the e matching is completed.

2. Self-locking learning method:

Press the controller learning on twice, the indicator light flashes twice quickly in the learning state, and then press any on you want to learn on the remote control to send a e. At this time, the indicator light flashes three times and goes out, and the e matching is completed.

3. Interlocking learning method:

Press the controller learning on three times, the indicator light flashes three times quickly in the learning state, at this time press the remote control A on, the indicator light flashes three times, and then press the remote control B on again, the indicator flashes three times and goes out, and the e matching is completed .

4. Learning method with a 5-second delay:

Press the controller learning on four times, the indicator light flashes four times and then press the remote control to send a e, the receiver indicator flashes three times and then the learning is successful, then press the remote control to send the e, the relay will automatically disconnect after 5 seconds of closing.

5. Learning method with a 10-second delay:

Press the controller learning on five times, the indicator light flashes five times and then press the remote control to send the e, the receiver indicator flashes three times and then the learning is successful, then press the remote control to send the e, and the relay will automatically disconnect after 10 seconds.

6. Learning method with 15 seconds delay:

Press the controller learning on six times, the indicator light flashes six times and then press the remote control to send a e, the receiver indicator flashes three times and then the learning is successful, then press the remote control to send the e, and the relay will automatically disconnect after 15 seconds of closing.

7. Learning method with a delay of 20 seconds:

Press the controller learning on seven times, the indicator light flashes seven times and then press the remote control to send the e, the receiver indicator flashes three times and then the learning is successful, then press the remote control to send the e, and the relay will automatically turn off after being closed for 20 seconds.




Clear data:

Press and hold the learning on for 8 seconds without letting go, the indicator light flashes once until the receiver indicator flashes 6 times quickly, the e clearing is successful