5PCS 5V 1A Micro/Type-c/Mini 18650 TP4056 Lithium Battery Charger Module

100% and high quality

Charge module- Linear charging.

Current- 1A adjustable.

Charge precision- 1.5%.

Input voltage- 4.5V-5.5V.

Full charge voltage- 4.2V.

Led indicator- red is charging Green is full charged.

Input interface- micro USB.

Work temperature- -10° to +85°.

Inversed polarity- NO.

Size- small to 25X19X10mm.

NOTE:

1. Ampere meter can only be connected to 5v input end of the module. 2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. 3. The connection wire should not be too thick. 4. Make sure the connect point is good. 5. If the input voltage is too high, like 5.2v, the current will be le than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to . 6. NO Reveral polarity.

Package Included:

5V Micro USB 1A 18650 Lithium Battery Charging Board Charger Module

The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly.

The first time you acce the battery, it may no voltage between the output OUT + and OUT-, then acce 5V voltage charge your energy can activate the protection circuit, and the battery from the B + B-, then draw a line on the short open also need recharged to activate the protection circuit. Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge

+ MICRO USB female and - pads for the power input, acce 5V. B + positive then the lithium battery, B- then negative lithium batteries. OUT + and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load.

Connect the battery to the B + B-, inserted into the USB female mobile phone charger, the red light is being charged, the green light to full.

Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery,

And still retains the input voltage wiring pads, can be very convenient DIY

Input voltage: 5V

Charging cut-off voltage: 4.2V ± 1%

Maximum charge current: 1000mA

Battery over-discharge protection voltage: 2.5V

Battery overcurrent protection current: 3A

Board size: 2.6 * 1.7CM

The TP4056 is a complete single-cell Li-Ion battery with a constant current/constant voltage linear charger. The SOP40 package with heatsink on the bottom of the TP4056 and fewer external components make the TP4056 ideal for portable applications. The TP4056 is suitable for USB power and adapter power supplies. Due to the internal PMOSFET architecture and anti-reverse charging path, no external isolation diodes are required. Thermal feedback automatically adjusts the charge current to limit temperature during high power operation or high ambient temperature conditions. The charging voltage is fixed at 4.2V, and the charging current can be externally set by a resistor. When the charging current drops to the set value of 1/10 after reaching the final float voltage, the TP4056 will automatically terminate the charging cycle. When the input voltage (AC adapter or USB power) is removed, the TP4056 automatically enters a low current state, reducing the battery leakage current to le than 2uA. The TP4056 can also be placed in shutdown mode when there is a power supply, reducing the supply current to 55uA. Other features of the TP4056 include battery temperature sensing, undervoltage lockout, automatic recharge, LED status pins for charging and termination. 100% and high quality Charge module:Linear charging. Current:1A adjustable. Charge precision:1.5%. Input voltage:4.5V-5.5V. Full charge voltage:4.2V ± 1% Led indicator:red is charging Green is full charged. Input interface:micro USB/mini usb/type-c usb Work temperature:-10° to +85°. Inversed polarity:NO. The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a NOTE: 1. Ampere meter can only be connected to 5v input end of the module. 2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. 3. The connection wire should not be too thick. 4. Make sure the connect point is good. 5. If the input voltage is too high, like 5.2v, the current will be le than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to .

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.