7A 160W Motor Drive Module 12V 24V Dual Channel DC Motor Driver Modul

Detailed Information About The Product:

1. Double H bridge which can drive two DC motors single 7A current high power; Wide voltage input 6.5V ~ 27V; Signal optocoupler isolation input IO port can be directly controlled without interference; Undervoltage protection to prevent instantaneous high-current burned module; High-power and electrostatic discharge circuit inhibit the transient interference pulse and static enhanced EMC performance stable and reliable product industrial design.
2. Power supply voltage 6.5V-27V power supply must not be connected to or over 27V otherwise it may burn out the module it is recommended that the power input in series 1 fuse.. Dual motor interface each rated output current 7A current 50A the motor interface must not short-circuit the proposed series 10A fuse. Control signal voltage 3-6.5V respectively is the enable signal and the positive inversion control signal.
3. Enable signal terminal input PWM adjustable speed PWM frequency range 0-10KHZ PWM minimum pulse width 10us. Working temperature -25 ℃ -80 ℃. Installation hole diameter: 3mm attention should be paid to prevent short circuit on the back of the circuit you can add insulation pad or copper column to raise the circuit board.
4. Suitable for motor parameters: Rated voltage 24V of the motor the appropriate identification of rated power 115W and below or rated current of 7A or less the following long-term work of the motor. Rated voltage 12V of the motor the appropriate identification of rated power 40W and below or rated current 7A rated below the motor for a long time full of work.
Precautions: 1. Drive power must not be reversed the proposed power connector in series 1 fuse the voltage should be between 6.5 ~ 27V. If the voltage is over-voltage power-on may burn module. 2. It is recommended that the rated output current of the power supply should be at least 2 times of the rated current of the motor so that the power supply can not supply the required voltage when the motor starts. Off the output lead to the phenomenon of motor pause. 3. Do not short-circuit the motor interface or may burn the driver module the proposed electrical interface in series 10A fuse.
4. In the forward and reverse switch when the need to brake 0.1S above and then reverse not in the motor has not stopped when the commutation or it may damage 5. Drive module power-down do not directly or indirectly high-speed rotation of the motor or motor generated electromotive force may
Burn module. If the application requires a high-speed rotation of the motor when module is powered down it is recommended.
The motor interface of the driver is connected in series with a relay NO and COM terminals and the relay coil and the driver are connected in common. In this way when the power down the relay disconnect and the motor connection.
6. CAUTION Do not expose to moisture. Do not short-circuit the components on board. Do not touch the pins and pads on the board.
7. Before you use the baby carefully read the description as a result of damage caused by improper use of the module do not change
Note: Where 0 is low 1 is high level x is any level when floating high.
color:Red
Material:PCB
size:55 x 55 x 16mm Package Contents:
1 x DC Motor Driver Only the above package content other products are not included.
Note: Light reflection and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
About Us
We provide the good product with the best pricewe support Wholesale/Drop Shipping Order
1. For Drop Shipping order please remark"dropshipping order" we will prioritize it.
2. For Wholesale/Drop Shipping orders if you have any ideas about the price or packageplease contact us in advancewe will give you the best service to satisfy your demands.
About Shipments
1.We will send out the orders ASAP once your payment is completed normally.
2.Please write your complete delivery address with correct phone number and zip code especially please confirm your full name.
About After-sale Service
We are reliable seller and we have our professional after-sale service for all of our customers. If there is any question about the orderplease contact us in advance we will always here until you get a happy answer.
About Feedback
1. Please check the package and item when you get carefully to make sure there is no problem.
2. If you have any problem or are not entirely satisfied with your packageplease don’t be hesitate to contact us first before leaving negative feedback. We will resolve the problem to satisfy you.
3. If there is no problem please leave us five star positive feedback.
Your affirmation is our greatest motivation ! ! !