Car Exhaust Flame Ignition Rev Limiter Launch Control Flame Controller Thrower Kit Universal

Car modification New car fire dragon tail fire extinguishing device Fire nozzle exhaust fire-breathing deviceApplicable models: Generalmaterial: plasticColour: Blacktfire method tfire method:1. Hot car needs more than 10 minutes, the exhaust needs no air.2. Pull the speed to 3500~6500 rpm, hold down the switch and lightly step on the throttle one-third to one-half. (Half of a second) Eyesight speed. At this time, the speed will turn from 6500 down, then you will hear To the sound of fire, the switch can be released, and at the same time, the throttle is continued. At this time, the speed will be pulled bato 6500 rpm. Repeat this action to continue the fire.Note: If you repeat the above action, if the rotation speed drops to 1800 rpm, there is no fire, the switch must be released, and you must not "pre" to turn off the engine. In severe cases, it will damage the engine.The installation method is below the product display.

First, the installation tool: 1. Three use the meter 2. Frequency table 3. Iron 4. Sciors 5. Cro screwdriver 6. Wire 7. nose 8. Electric

Second, direct ignition and distribution disc ignition installation precautionsDirect ignition2.Distribution of electric ignition to any vehicle When installing this product, please note that the outlet of the end of the exhaust should not be too small. It is recommended to use a tail with a diameter of more than five centimeters, or an exhaust tail .Direct Ignition Installation Precautions 1. When the car ignition power is cut off, the "Computer Fault Light" may not be on. 2. nozzle should pay special attention to the positive and negative electricity when installing the wiring of the nozzle. If the connection method is wrong, there is a poibility of ing the computer. 3. The line paing through the fire wall should prevent the wire from g crushed and cause a short circuit. 4. The "Coal" in this product is installed at the bottom of the rear trunk, close to the spare wheel, and it must be securely fixed. 5. The "" in this product should be locked at the end of the exhaust approximately one centimeter away from the outlet. At the lowest end, the ignition distance should be controlled at 2mm.Dispenser Ignition Installation Precautions 1. Find out the correct position of the ignition inside the distribution board. 2. The wiring of the ignition in the distribution board to the flameproof control box in this product must not be wrong, otherwise the distribution board may be ed out. 3. When the car ignition power supply is cut off, the "computer fault light" may not be on. 4. The line paing through the fire wall should prevent the wire from g crushed and causing a short circuit. 5. The "Corl" in this product is installed at the bottom of the trunk and close to the spare tire. It should be fixed. 6. The "ignitor" in this product should be locked at the end of the exhaust approximately one centimeter away from the exit, and the lowest end, the ignition distance should be controlled at 2mmThird, the nozzle wiring installation method nozzle wiring installation method:1. It should be known first that the 's signal line is positive or negative, and most of the vehicle types are negative.2. How to find out which of the two lines of the connector is the signal cable, first unplug the connector, and then measure the positive and negative poles of the two wires on the side of the utility meter. If there is a positive power and one power is not available, No power should be the signal line. Another method is to use a frequency meter to measure the two wires of the line. The frequency is the signal line.3. The positive and negative electric wires of the s should be attached with special attention to the color of the flameproof control box. 4. The positive and negative electricity should be p special attention when installing the wiring. If the connection method is wrong, there is a poibility of ing the computer.Fourth, troubleshooting If you do not have to fire when you should pay attention to:1. Whether the wire connector of the fire control box is off or bad2. Is the fire switch damaged and the switch's plug dropped?3. Whether the plug for car test has power supply, including positive power and ground4. The fire-breathing dragon control box to test the ear of the car after the wire, with or without damage.5. Whether the wires to the ignitor of the car after the are damaged or not are not damaged.6. Is the ignition spacing on the too large or too small (