Digital clamp multimeter, digital multimeter

Product Details

Description

This multimeter DT266 Mainly for measuring DC and AC voltage, AC current, resistance and diode,with continuity buzzer, data hold and insulation test function. is Best device for home repair. It is a good assistant to test and troubleshoot faults that exist in electronic device. This Digital LCD Multimeter can test Voltmeter Ohmmeter Ammeter. Clamp Meter for your day to day needs Multi-Purpose for Professional & Home Use If you have basic knowledge about Multimeters you can try this small Multimeter for basic continuity checks & Voltage Meaurements & also can be used for Heavy Ampere measurement in heavy load wires Description 1. Functions DCV ACV ACA Resistor (ohms) Buzzer 2. Display 4.75 cms length, 15mm high LCD. General Powered by 9V Battery Inside Dimensions Multimeter : 24 cms(Length) X 9.5 cms(Width including clamp handle(6.75 cms without clamp handle)) X 3.5 cms (Thickness) Function Range Accuracy DC Voltage 1000V (0.5%+1dgt) AC Voltage 200-750V (1.2%+4dgt) AC Current 200A-1000A (2.5%+5dgt) Resistance 200Ω-20KΩ (1.0%+2dgt)

Key Features

The digital clamp meter comprises features Common Function: 3 1/2 digits LCD,

Max. reading 1999;

Data-Hold Function;

Low battery indication;

Plug-in insulation tester adapter 500VDC; DCA+ACV+ACA+OHM;

ACCESSORIES: Test lead;9V Battery(AA) Inside ; Users Manual;

DC Voltage 1000V ±(0.5%+1dgt)

AC Voltage 200-750V ±(1.2%+4dgt)

AC Current 200A-1000A ±(2.5%+5dgt)

Resistance 200Ω-20KΩ ±(1.0%+2dgt)

Continuity Buzzer Yes Data Hold Yes Power Supply 9V Battery 6F22

Maximum Display 1999 Display Size 14×47mm Product Net Weight 350g

A multimeter with built-in clamp.

A clamp meter measures the vector sum of the currents flowing in all the conductors passing through the probe, which depends on the phase relationship of the currents.

A relatively recent development is a multi-conductor clamp meter with several sensor coils around the jaws of the clamp. This could be clamped around standard two- or three-conductor single-phase cables to provide a readout of the current flowing through the load,[3] with no need to separate the conductors.

The meter reading divided by the number of turns is the current,[4] with some loss of accuracy due to inductive effects.

Clamp meters are used by electricians, sometimes with the clamp incorporated into a general purpose multimeter.

It is simple to measure very high currents (hundreds of amperes) with the appropriate current transformer. Accurate measurement of low currents (a few milliamperes) with a current transformer clamp is more difficult.

Columbia iron vane type clamp-on ammeter, with heads for different ranges

Less-expensive clamp meters use a rectifier circuit which actually reads mean current, but is calibrated to display the RMS current corresponding to the measured mean, giving a correct RMS reading only if the current is a sine wave. For other waveforms readings will be incorrect; when these simpler meters are used with non-sinusoidal loads such as the ballasts used with fluorescent lamps or high-intensity discharge lamps or most modern computer and electronic equipment, readings can be quite inaccurate. Meters which respond to true RMS rather than mean current are described as “true RMS”.

Typical hand-held Hall effect units can read currents as low as 200 mA, and units that can read down to 1 mA are available.

Several jaw sizes are available for clamping around large conductors and bus bars up to 4 1⁄2 inches (110 mm) wide.[4] As the illustration shows, the scale is very non-linear and unsuitable for measuring low currents, with currents of less than half the full-scale deflection crammed into a short section of the dial

1× multimeter