Door suction lo control vacPSE motor for Benz W140 S300SE S400SE E-cl W210 E320 CLK320 430 C280 230 SL-cl

RM15482498114054375

The motor is completely identical to the electric motor, it allows restoring the efficiency of the PSE vacuum , and a cooler for cooling the collector and brushes is additionally installed. Motor suitable for PSE compreors: A1408000448 A1408000648 A1408001048 A1408001148 A1408001948 A1408002048 A1408002148 A1408002248 A1408002348 A1408002448 A1408002548 A1408002848 A1408002948 A1408003048 A1408003148 A1408003248 A2108001148 0132006323 0132006324 0132006325 0132006342 0132006355 0132006350 0132006357 0132006367 0132006399 0132006899 1397220145 65590 JOHNSON 365002 66100 JOHNSON 332442 66100 JOHNSON 382211 Instructions for replacing the motor in a vacuum Mercedes W140 Repair of the vacuum W140 with a ed-out JOHNSON little engine is to rep Unscrew the torx screws and push the chips here on the contacts of the electric motor. To do this, you need to disaemble the PSE vacuum compreor, unscrew a pair of screws on the case (TORX T20). Next, open the case latch around the perimeter. After removing the bottom of the case, you need to unscrew the electronic board in the unit (TORX T7). After that, you need to push the metal contacts of the chips and s from the outside, the board out of the case. With it, pull the electric motor from the seat. To chethe operation of the motor of the vacuum , you need to unsolder one or all of the wires from it and apply 12V to it. To remove the body from the JOHNSON motor, you need to unscrew the 3 screws (TORX T10), remove the top cover of the , the stator ring, remove the plates from the rotor To remove the rotor retainer, you need to carefully two small slotted screwdrivers. To remove the rotor retainer, separate here. Separate the lower part of the from the metal base of the housing. Perhaps these parts will be d together with a sealant, then you will need to separate them with a clerical . After that, carefully remove from the motor shaft the lower part of the body together with the rotor and the retainer. We change the engine observing polarity, on the engine plus it is indicated by a red mark. And we collect everything in re order. ATTENTION! After replacing the motor, chethe vacuum system for leaks (swapping tubes, doors, head resints, hatch, trunk, etc.). Chethe imr for wedging. Moisture is not allowed in the . Do not let the run for a time, more than 7 seconds - WILL UP! Please verify the part number on your vehicle before ordering. All parcels are sent by airmail on the same day or the next (except holidays and weekends). The parcel is sent by the economical carrier, because for you the delivery is free. But, as everyone knows, economical delivery can not be fast. It can take both 7 days and 30 days. And therefore, please pay attention to this before ordering. Unfortunately, we can not in any way affect the speed of delivery. Thank you for understanding.

AZGIANT for Mercedes-Benz W220 S280 S320 S350 S430 S500 S600 door suction motor door lo control motorAs the use time increases, the door generally has probl with poor door suction.The cause of this problem1. Door leaking2. The door sinks3. Door suction motor fatigue.D SHAFT 1SUITABLE FOR::1992-1993 Mercedes-Benz 300SE1992 Mercedes-Benz 400SE1993 Mercedes-Benz 400SELD SHAFT 2SUITABLE FOR:1999-2000 Mercedes-Benz E320 clk320 c280 clk430 c230MERCEDES-Benz E-CL w210O SHAFTSUITABLE FOR:2003-2006 Mercedes-Benz SL5002003-2008 Mercedes-Benz SL55 AMG2007-2012 Mercedes-Benz SL5502004-2009 Mercedes-Benz SL6002009-2012 Mercedes-Benz SL63 AMG2005-2011 Mercedes-Benz SL65 AMG2003-2012 Mercedes-benz R230 SL500 SL55 AMGAfter the battery is disconnected and reconnected, the information stored in the computer, including the fault information, is cleared and the door suction is working normally.However, after a certain period of time, the computer will record the faulty door suction and work abnormally. For example, the fatigue of the door suction motor may cause the motor working current to increase the motor overheating and other faults.The computer will fail to protect the door stop. Under normal circumstances, the door suction motor can be repd without leaking and the door sinking to repair the fault.