DTC2210 AC 110V 220V Digital Microcomputer Thermoregulator Thermostat Temperature Controller Cooling Heating Switch Dual Display

DTC2210 AC 110V 220V Digital Microcomputer Thermoregulator Thermostat Temperature Controller Cooling Heating Switch Dual Display

Description: Power supply voltage: AC110 ~ 230V Temperature range: -40 ℃ ~ + 99 ℃ Temperature measurement accuracy: ± 1 ℃ (-40 ℃ ~ + 70 ℃) r line length: 100cm Thermostat size: 93mm * 56mm * 34mm Output capacity: cooling (10A / 250VAC) heating (10A / 250VAC) Parameter setting method: When the thermostat is working normally, pre and hold the key for more than 3 seconds to enter the parameter modification mode, the digital tube displays the code of the first menu item "F1", pre or to increase or decrease the code of the menu item, pre and hold the key , Short pre or key to increase or decrease and display the parameter setting value of the current menu; hold down the key, while long pre or key to quickly increase or decrease and display the parameter setting value of the current menu. At the same time, long-pre the and keys to restore the parameters to the factory settings. Operating instructions: When the thermostat works normally, pre and hold the power on for more than 3 seconds to turn off the thermostat. When the thermostat is off, pre and hold the power on for more than 3 seconds to turn on the thermostat. When the thermostat is working normally, the digital tube displays the current temperature measurement value, and performs automatic recognition and conversion of the cooling and heating working mode. When the measured temperature ≥ temperature set value + temperature difference set value, enter the cooling state, the Cool indicator lights, the refrigeration relay normally open contact is closed; The Cool indicator flashes, indicating that the refrigeration equipment is in the state of delay protection of the pre; when the temperature is measured ≤The temperature setting value, the Cool indicator is off, and the normally open contact of the cooling relay is disconnected. When the measured temperature ≤ temperature set value-temperature difference set value enters the heating state, the Heat indicator lights, the heating relay normally open contact is closed; when the measured temperature ≥ temperature set value, the Heat indicator turns off, the heating relay normally open contact disconnect. Cool indicator: On: cooling operation; off: cooling off; flashing: pre delay Heat indicator: On: heating work; off: heating off note:Cool and Heat LEDs cannot be on at the same time Repair system data: After the thermostat is powered on, first check whether the parameter settings are correct. If an error is detected, “Er” is displayed. At this time, pre any key to restore the default parameter settings and work normally. It is recommended to reset the parameters at this time. System code, reason and action: r failure alarm: When the temperature probe circuit has a short circuit or open circuit failure, the thermostat activates the probe failure alarm mode and closes all execution states. The digital tube displays "EE". After the failure is removed, pre any key to return to the normal working mode. Over temperature limit alarm: When the temperature measurement exceeds the temperature measurement range, the thermostat activates the over temperature limit fault alarm mode, closes all execution states, the digital tube displays "HH", when the temperature returns to the normal measurement range, pre any key, Return to normal working mode. Safety rules: Danger: 1. Strictly distinguish the r lead, power cord and output relay interface, not to be connected wrong, and the relay must not be overloaded; 2. All wiring changes must be made with the power disconnected. Warning: 1. This thermostat is forbidden to be used in water or exceively humid envment. It is prohibited to use in high temperature, strong electromagnetic interference and strong corrosive envment. Note: 1. The power supply voltage should be consistent with the voltage marked by the thermostat, and ensure the stability of the power supply voltage; 2. To avoid poible interference, it is recommended that the r leads should be kept at an appropriate distance from the power line. Package Included: 1 x LED Thermometer 1 x DS18B20 Temperature r Probe 1 x English Manual About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.