NCV Digital Multimeter 6000 Counts Auto Ranging AC/DC Voltage Meter Tester

Model

DM66

DM616

DM6S

Range Selection

Manual Range

Auto Range

Intelligent Shift

Maximum Count

6000

6000

6000

Maximum Display

5999

5999

5999

True Effective Value

No

Yes

No

DC Voltage

Ye

Ye

Ye

AC Voltage

Ye

Ye

Ye

DC

Ye

Ye

Ye

AC

No

Yes

Yes

Zero FireWire Identification

Ye

Ye

Ye

Resistance

Ye

Ye

Ye

Capacitance

No

Yes

Yes

Temperature

Yes

Yes

No

diode

Ye

Ye

Ye

On and off beep

Ye

Ye

Ye

NVC

Ye

Ye

Ye

frequency

No

Yes

Yes

Duty cycle

No

Yes

No

Data retention

Ye

Ye

Ye

Digital display backlight

Ye

Ye

Ye

Automatic shut-down

Ye

Ye

Ye

Flashlight lighting

Ye

Ye

Ye

Low battery reminder

Ye

Ye

Ye

Fuse

2pc

2pc

2pc

DM616

1. A continuity test of a circuit without delays both on closing, and on opening.

2. In mV mode, measurements start from 0 (for other multimeters, the dead zone is from 0 to 5). 3. Automatic limit selection works correctly witsignals with a large crеst-factor.

The difference between three models: DM66 / DM616 / DM6S.

Model: DM66

DC Voltage: 600mV/6V/60V/600V

AC Voltage: 600V

DC: 600μA/6mA/60mA/600mA/10A

AC: -

Resistance: 600Ω/6kΩ/60kΩ/600kΩ/6MΩ

Capacitance: -

Frequency: -

Temperature: -20℃~70℃

Duty Cycle: -

Model: DM616

DC Voltage: 60mV/600mV/6V/60V/600V

AC Voltage: 60mV/600mV/6V/60V/600V

DC: 600μA/6mA/60mA/600mA/10A

AC: 600μA/6mA/60mA/600mA/10A

Resistance: 600Ω/6kΩ/60kΩ/600kΩ/6MΩ/600MΩ

Capacitance: 9.999nF/99.99nF/999.9nF/9.999μF/99.99μF/999.9μF/9.999mF/99.99mF

Frequency: 99Hz/999.9Hz/9.999kHz/99.99kHz/999.9kHz/9.999MHz/99.99MHz

Temperature: -30℃~0℃/0℃~400℃/400℃~1000℃

Duty Cycle: 10-95%

No bargraph scale.

Model: DM6S

DC Voltage: 600V

AC Voltage: 600V

DC: 200mA

AC: 200mA

Resistance: 6kΩ/60kΩ/600kΩ/6MΩ/10MΩ

Capacitance: 600μF/6000μF

Frequency: 1000Hz

Temperature: -

Duty Cycle: -

DM616 with auto range.

NCV can detect the line without touching the line, find the voltage and iue a drop alarm.

DM616 can measure capacitance, DM616=multimeter + capacitance meter.

Full-range overload protection

Electronic part: PTC thermistor protection,

Intelligent anti-burn;

Current: Double ceramic fuses effectively avoid

Burn-free watch, safer to use.

DM616 28mm Character LCD Display; Maximum display value 5999; With LCD backlight.

The DM616 is designed with a strong light on the top of the fuselage, which is convenient for normal work at night and in a dark environment, making your work safer.

DM616 Digital Multimeter Temperature Measuring range: "-30 ~ 1000 ℃".

DC voltage measurement 1. Plug the black meter into the COM jack and the red test lead into the V / Ω jack. 2. Set the function switch to the DC voltage range V-range range, and connect the test lead to Power to be tested (measured for open circuit voltage) or load (measured for load voltage drop), red test lead The polarity of the contact will be shown on the display at the same time. Note: 1. If you do not know the voltage range to be measured, set the function switch to the maximum range and gradually decrease. 2. If the display only shows “ol”, it means over range, and the function switch should be set to a higher amount. Cheng 3. Do not measure voltages higher than 600V, it is poible to display voltage values with higher voltage values Yes, but there is a danger of damaging the internal wiring. 4. When measuring high voltage, pay special attention to avoid electric shock. AC voltage measurement 1. Plug the black test lead into the COM jack and the red test lead into the V / Ω jack 2. Set the function switch to the AC voltage range V ~ range, and connect the test lead to On the power supply or load to be tested, the test connection diagram is the same as above. When measuring AC voltage, there is no Polarity display. note: Do not input a voltage higher than 600V, it is poible to display a higher voltage value. Danger of bad internal wiring. 1. Select the range: If the current is unknown, the maximum range should be selected. Measurement method: 1. Remove power from the circuit. 2. Disconnect or unsolder the circuit to create a position where the multimeter probe can be inserted. 3. Select A ~ (AC) or A- (DC) as required. 4. Plug the black test probe into the COM input jack. Depending on the expected reading, plug the red test probe into the amp or milliamp input jack. 5. Connect the probe tip at both ends of the disconnection point so that all current flows through the digital multimeter (in series). 6. Reconnect power to the circuit. 7. Check the readings, pay attention to the unit of measurement. About shipping
Shipping and Packaging All items will be double checked and well packed before sending.Items will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.