QC2.0 QC3.0 LED Dual USB PD PPS Fast Charge MobileModule 100W Type-C 18650 Charging Module Support AFC FCP VOOC

Features:

Multi-interface design, there are 4 USB ports,Type-C1, Type-C2,Type-A1, Type-A2

Easy to use, wide range of application

High efficiency, high precision and high reliability

Portable mobile power module

Digital screen display




Parameters:

Battery type: lithium polymer battery

Maximum output power: 65W/100W




The default is digital tube power display:

The mainboard has four USB ports by default,Type-C1, Type-C2,Type-A1, and Type-A2.

Type - C1, the Type - C2 support an AFC/FCP/SCP/voOC PD3.0 / PD2.0 quick charge input.

Support the AFC/FCP of PPS/PD3.0 / PD2.0 / / QC3 + / QC3.0 / QC2.0 / SCP quick charge output.

Type-A1/Type-A2 supports Apple/AFC/FCPvoOC/QC3+/QC3.0/QC2.0/SCP fast charge output.

Type-C1 and Type-C2 support input/output fast charging.

Input support: 5V/9V/12V/15V/20V voltage.

PPS output support: 3.3V-21V/3A.

PD3.0 / PD2.0 output support: 5 v3a / 9 v3a / 15 v3a 12 v3a / / 20 v5a. (Type-C2 only supports 60W)

QC2.0 output support: 5V3A/9V3A/12V3A.

QC3.0 Support: 5V-12V output voltage, 200mV/Step.

AFC output support: 5V3A/9V2A/12V2A.

Input support: 5V/9V/12V voltage.

FCP output support: 5V3A/9V2A/12V1.5A.

Input support: 5V/9V/12V voltage.

SCP output support: 5V4.5A, 10V2.2A.

The value can be 5.5V3A.

VOOC output support: 5V@4A.

Supports simultaneous discharge of TypeA1 / TypeA2 /Type-C ports.

Maximum 5V@3A, to fast charge please single port use.

Product size: 72x27x6mm




Note:

1: The motherboard external battery line must be able to pass 10A current, at least with more than 1 square copper wire, ordinary line to use 1.5 square. It doesn't have to be too thick, but it shouldn't be too thin. Too thin could be a safety hazard. (because there is a lot of current at the battery end)16AWG cable is recommended.

2: The motherboard comes with a protection chip, only support 2-5 series of batteries, 6 series of lithium iron phosphate need the battery comes with a protection board, with the protection board over current protection current must be greater than 15A, otherwise it can not work properly, seriously damage the motherboard chip.

3: Because the current at the battery end is too large, the battery must be welded with a thick wire to test. The charging and discharging can not be tested by holding the welding pad with an alligator clamp. Be sure to do so this shop refuses after-sales service.

4: Select the battery can use 4.15V/4.2V/4.35V/4.4V 18650, polymer, ternary lithium battery, large monomer can be used, single battery capacity does not exceed 25000mAh, more than the power display will be inaccurate. 3.65V lithium iron phosphate is supported, but disposable dry batteries, nickel-metal hydride, nickel-chromium, and lead-acid batteries are not supported. The minimum battery string is 2, the maximum battery string is 6, and the total voltage cannot exceed 23V. The charge and discharge flow of a single series battery should be at least 10A. If the charge and discharge flow cannot reach 10A, turn down the power.

5: The motherboard must be preset battery capacity, please see the details inside the introduction.

6: Supports OPO flash charging and HW super fast charging. Different protocols have different power. 65W and 100W are the power of PD protocol, and 20W for VOOC and 22.5W for SCP. Please confirm the demand before shooting, do not accept or support your phone can not be charged quickly on the return. Welded goods do not support return or replacement. (Phones that are not supported are not available to third parties because the phone has its own protocol.)

7: This motherboard connected to the battery must meet the requirements and to series, if your battery is ordinary capacity small current single or multiple parallel battery please refer to other types of motherboard.




Product list:

1X module