RongYin A5 MiniType-C Charging UHF 400-470Mhz 16CH Scrambler Wireless Frequency Copy Kid's Gift Range Radios

Rongyin  A5  Mini Walkie Talkie
(USB-C Charger)
UHF:400-470 MHz
Wireless frequency copy

Using the Type-C USB Charger

The Type-C USB charger is a handy port that allows you to conveniently charge your Li-ion battery pack.

1. Make sure your radio is turned OFF.

2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. The other end of the data line is connected to the output port of the power bank or the adapter of the mobile phone.

3. An empty battery will be fully charged in 4 hours.






Fast frequency matching 

Select channel to channel 1, press and hold the [VOL-] and  key to turn on the radio. The voice will announce "Power On" to enter the sweep function and the green light will flash; Press the [VOL-]key to prompt a "beep" sound and the green light remains on, and start scanning. After scanning, it will be automatically stored and prompted with two beeps. (The green light remains on during scanning, and the green light flashes when scanning is stopped)

Rotate to channel 2, press the [VOL-] key to continue scanning. After scanning, it will be automatically stored and prompted with a "beep" sound, with the indicator light as described above;

Rotate to channel 3 and press the [VOL-] key to continue scanning. After scanning, it will be automatically stored and prompted with a "beep" sound; Operate in sequence until channel 16.

Complete the frequency sweep task, shut down and restart to exit the frequency sweep mode, and the frequency sweep task ends.


Wireless Replication 

Select channel to channel 2, press and hold the [VOL-] and key to turn on both the transmitter and receiver. The receiver and transmitter prompt "beep" to enter wireless replication. When the transmitter presses the [PTT] key, the red light remains on, and the receiver green light automatically remains on. Copy all the configuration parameters of channels 1-16 of the transmitter, and the receiver prompts "beep" twice to complete the replication. Both prompt lights turn off and automatically restart, the replication task has ended.





Monitor

Note: To use this, pre program the [SK1/VOL+ ] or [SK2/VOL-] keys as Monitor function keys.

The Monitor feature is for excluding (opening) the Squelch, in order to listen to signals that are too weak to keep the Squelch permanently opened. Hold down the [MONI] key to enable such function.


Scrambler

The scrambler is designed to protect communications. This feature prevents parties of other networks from hearing and understanding your voice communications. Set the scrambler function on or off through programming software.

 
 


• UHF400-470MHz Transceiver
• Output power: Max 2W
• Channel spacing: 12.5 KHz/25.0 KHz
• Channel Scan
• Vocal tuning
• Battery save
• Channel Monitor
• Squelch
• 50 CTCSS tones and 210 DCS codes
• TOT (Time out timer)
• 2pin Kenwood accessory jack
• Scramble function
• Frequency scanning function
• Power on/off and volume adjustment 
• Channel selection
• Talking on Your Radio
• CTCSS/DCS tones
• Fast frequency matching
• Scrambler
• Time-out Timer (TOT)
• Automatic power save feature
• Low battery alarm
• English/Chinese language setting
• Emergency Alert
• Voice Operated Transmit（VOX）

if you buy 1pcs
1*Radio Body

1*Battery 

1*Belt Clip

1*Manual

1*AC/DC adapter 
1*Type-C Cable

if you buy 2pcs

2*Radio Body

2*Battery 

2*Belt Clip

2*AC/DC adapter 
2*Type-C Cable
1*Manual


Note:We will send you the item of your choice. (Please check your selected sku carefully before placing your order)

Frequency Range：400-470MHz

Memory Channel：16

Operation Voltage DC： 3.7 V ±10%

Transmission current ：≤1200mA

Receive Sensitivity：0.25μV (12dB SINAD)

Emission Designator：11k0F3E

Audio Power Output：1W @8 ohms

Receive current ：≤380mA

Rated Audio Distortion： ≤5%

Connection for accessories： 2 pin Kenwood jack

Antenna impedance：50 Ohm