TEC-06 LED Battery Capacity Tester 16W Electric Load Tester With Fan Single

TEC-06 LED Battery Capacity Tester 16W Electric Load Tester With Fan Single Version/Online Version For Tester Max 500AH

The online version can be connected to a computer to draw a discharge curve, or it can be used in stand-alone mode. The online line is the power supply line. The stand-alone version cannot be connected to the computer and needs to be equipped with a power supply cord. Note : The stand-alone version cannot be connected to a computer and requires an additional power supply line. 1.Description: TEC-06 is constant current electronic load.It uses high-precision DAC loop control technology to control output current for power supply or battery.So that the current does not change with the voltage changes.It is a load its, no longer need another external load discharge. This is a linear electronic load, not a PWM mode TEC-06 will automatically calculate the product of discharge current and time , to detect the battery capacity. TEC-06 can also be used as an electronic load to verify the battery or power output capacity. 2.Parameter: 1>. Max Current: 3.5A; error: . Max Power: 16W 3>. Operating Temperature: -20~70 Celsius 3.Features: 1>. Can not connect computer and draw discharge curve 2>. Encoder switch (shuttle) operation, easy and convenient 3>. Precise current, the full range error is within 0.5% 4>. Integrated fan, discharge power can be up to 16W; and the fan will be auto on/off according to the power 5>. Support 4-wire measurement, and it can measurement battery internal 6>. Max connection voltage 15V, and power-off voltage can be adjusted randomly in the range of 1.0-12V; step length 0.05V 7>. When the battery current is not enough, the detector will automatically adjust set current until the actual current meets the set value; when the actual current is lower than 40% set value, the detector will end up discharging 8>. MINI USB interface (5V voltage) power supply, and the actual current consumption is within 240mA 9>. Max detection capacity is 500000mAH (500AH) 10>. Adopt 4-wire battery clip, and it can measure internal resistance 4.Use steps: 1>. Turn on the power,Make sure the type of battery and set the turn-off voltage; 2>. Connect battery to I+ and I+.If need measure internal resistance of the battery need to use four-wire.and the voltage measuring terminal is connected to the detector. 3>. Set the turn-off voltage: Turn the knob switch to the "off voltage", pre the switch, then LED lights all bright."Turn off voltage" lights flashing,means that the turn-off voltage into the set state, turn the knob, you can change the size of the shutdown voltage.the minimum adjustment step is 0.05V, to the required set value, then pre the switch The parameter is stored in the detector to complete the turn off the voltage parameter settings. 4>. Set the current: Turn the rotary switch to the "current" display mode. The setting method is the same as above. The adjustment step is 50mA within 500mA.The adjustment step is 100mA above 500mA.the maximum current is 3.5A. 5>.Start/Stop: start there are two modes, "mode 1" is in the "capacity" display state pre the switch to start (start and then pre the switch is paused), this start method measured battery voltage is the battery open circuit voltage, Measuring the battery should use this start method, this mode if the use of 4-wire battery clip input, you can measure the battery resistance. "Mode 2" is in the "measured voltage" display mode pre the switch, the starting method of the measured voltage is the line voltage, power supply or should be activated in this mode. After the start of the discharge LED lights began to flash, digital display discharge capacity. After the discharge starts the detector will heat, when the discharge power is greater than 2.2W fan start, if le than 2W fan closed. 6>. End: When the battery voltage is lower than the shutdown voltage, the detector stops discharging the battery, the measurement is completed, then the digital tube flashes and shows the final discharge capacity. 7>. Measure again: After completion of the measurement, the detector flashes and shows the capacity that has been completed. You must clear the capacity data to make the measurement, Long pre the switch for 3 seconds or re-power on to do this. 5.Special function: 1>. Maximum power limit function: TEC-06 can limit the maximum power of discharge, when the user set the discharge power is greater than 16W, the detector can automatically adjust the discharge current, so that the power within 16W. 2>. Battery discharge capacity detection function: When the maximum discharge current of the battery can not reach the set value, the detector will automatically reduce the discharge current. 3>. Cycle display function: In the "internal resistance" display mode, click the switch, the detector will automatically cycle to display five digital. Package Included: 1 x TEC-06 Battery Capacity Tester 16W Electric Load Max 500AH LED Display w/ Fan

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.