V3 1.2-12V ZB2L3 18650 Li-ion Lithium Battery Capacity Tester Resistance

V3 1.2-12V ZB2L3 18650 Li-ion Lithium Battery Capacity Tester Resistance Lead-acid Battery Capacity Meter Discharge Tester

Basic parameters: Power supply voltage: DC4.5-6V (micro USB interface) Working current: no more than 70mA Discharge voltage: 1.00V-15.00V resolution 0.01V Termination voltage range: 0.5-13.0V Support current: no more than 3.000A resolution 0.001A Voltage measurement error: le than 1% + 0.02V Current measurement error: le than 1.2% + -0.002A Test data range: 999.9Ah (Ah, 1Ah=1000mAh) or 9999Min (minutes) when the value is large, switch by decimal point shift, when it is lower than 10Ah, it is displayed as X.XXX, and above 10Ah, it is displayed as XX.XX, This type of push. Finished product size: 54mmX41mmX17mm (length X width X height) Board and acceories weight: host 25g, two 5W ceramic resistor 9g, 50W resistance about 27g (including line) How to use (default factory mode): 1. The battery under test should be fully charged first. 2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (please use the mobile phone charging head, do not use desktop or notebook USB power supply), the battery voltage is displayed at this time. 3. To start the test directly, just pre the “OK” on, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to pre the "+" or "-" on to modify the battery voltage display state, the termination voltage is displayed as the beginning of the flashing "E", the latter represents the voltage value, the resolution is 0.1V, after setting Pre "OK" to start the test. 4. After the test starts, the tester will turn on the electronic switch that controls the load. The test proce data will be displayed in the following order: current voltage (V), current discharge current (A), discharged capacity (Ah), discharge time (Min) ), the termination voltage E (V), you can manually switch the value by preing the "+" and "-" ons. When the battery voltage is lower than the termination voltage, the tester cuts off the load, and the display data stays on the capacity (Ah) and flashes rapidly along with the “Ah” indicator. The capacity displayed at this time is the actual discharge capacity of the battery. Pre any on. The data can be displayed stably. After that, pre the “+” and “-” ons to check the termination voltage, average voltage, average current, capacity and discharge time. Pre the “OK” on again to return to the power-on state to replace the battery test. section... Supplement 1: Modify the termination voltage during the test. Pre the “OK” on during the test. The tester will pause the test. At this time, the termination voltage can be modified. When the “OK” on is preed again, the test is resumed. Supplement 2: Stop the test during the test. Pre and hold the on “OK” during the test to stop the test. This operation will clear the tested data. Error code and meaning: Err1: Battery voltage is higher than 15V Err2: Battery voltage is lower than the set termination voltage Err3: The battery cannot withstand the load discharge current or the line internal resistance is too large Err4: The current is too large (current exceeds 3.1A) Err5: Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned) Tester function settings: Pre and hold the "OK" on to power on when the power is off. The tester enters the setting state. There are two settings. Pre the "+" and "-" ons to change the setting. Pre the "OK" on to confirm and save the settings. The two settings are as follows: 1. AUon: The automatic voltage recognition function is turned on, and the tester will set a termination voltage according to the empirical value each time the test is to be started. AUoF: The automatic voltage recognition function is turned off. Each time the test is started, the tester only calls the last saved termination voltage and does not automatically set it. The tester saves this value every time the terminal voltage is manually adjusted. 2. ALon: Automatic wheel display: The test proce values are automatically displayed between turns. ALoF: Automatic wheel display off: The test proce value is fixed and can only be switched manually. Note: If the battery is reversed, the circuit switch can be damaged when the load is turned on and the load current is large (about >0.8A)! ! Warranty description: Please check after receiving the goods, if the shell is crushed, please reject it directly! The effective time for handling the casing transport damage is within of the receipt date. 1. From the date of signing, the quality problem occurs within 0-7 days (including), free maintenance or return, the freight is paid by the seller, but please do not send it! 2. If there is a problem within 8-14 days (including) from the date of receipt, free maintenance, the freight will be borne by one side. 3. If there is a problem within 15-30 days (including) from the date of receipt, free maintenance, the freight is borne by the buyer. 4. If there is a problem from the 31st to the 180th from the date of receipt, the cost price will be repaired and the buyer will bear the freight. The following conditions are not included in the free maintenance scope, and all are charged for repair: If the board is not properly used or the function is miing, the power connector or the terminal is loose and damaged. The following conditions will not be repaired: If the plate is splashed with liquid or the metal body is short-circuited, the components on the board are damaged or even the board is deformed. The computer is used to damage the USB port of the notebook. The board is burnt and broken due to the reverse connection or exceive current. , s-calibration (the number of calibration records is greater than 1).

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.