915 Generation DC 12V 24V 36V 500W PWM Brushless Motor Controller with

Detailed Information About The Product:

Operating voltage: DC 12V-36V; Operating Current: less than equal 15A; Driver Power: less than equal 500W; Speed Voltage: 0.1V-5V; Operating Temperature:-40-85C; Humidity: 90%RH
Stall protection:Yes; Enable Control: Yes; Over-current protection: Yes; Steering control: Yes; Speed control signal: Yes
Size: 63 x 42 x 17mm(L x W x H); Probe size 3mm,length: fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out: VCC(positive power supply), GND(negative one), MC(motor phases W), MB(motor phases V), MA(motor phase )
Set for the control side: GND control terminal ground, VR the governor end 0-5V(corresponding to 10% of motor speed -100%), ZF reversing control(connected to 5V or ground can charge the motor rotation direction), M tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number), EL enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops), 5V control terminal

HALL for the hall terminals:
5V, Hall power positive
Ha, Hall signal
Hb, Hall signal
Hc, Hall Signal
GND, Hall negative
Wiring:
Control terminal for SET:
1. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster
2. Motor steering control wiring methods: you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V
3. Pulse speed signal: high and low output . IC can not understand the information with the customer request
Hall signal inputs for hall:
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor hal signals positive, GND power supply negative signal to the motor hall
Note: Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the sequence, need to be adjusted, please parents who pay attention! If the line sequence wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!
color:Blue
Material:PC+Metal

Package Contents:
1 x PWM Brushless Motor Controller

Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

About Us
We provide the good product with the best price,we support Wholesale/Drop Shipping Order
1. For Drop Shipping order, please remark"dropshipping order", we will prioritize it.
2. For Wholesale/Drop Shipping orders, if you have anyeas about the price or package,please contact us in advance,we will give you the best service to satisfy your demands.

About Shipments
1.We will send out the orders ASAP once your payment is completed normally.
2.Please write your complete delivery address with correct phone number and zip code, especially please confirm your full name.

About After-sale Service
We are reliable seller and we have our professional after-sale service for all of our customs. If there is any question about the order,please contact us in advance ,we will always here until you get a happy answer.

About Feedback
1. Please check the package and item when you get carefully to make sure there is no problem.
2. If you have any problem or are not entirely satisfied with your package,please don’t be hesitate to contact us first before leaving negative feedback. We will resolve the problem to satisfy you.
3. If there is no problem, please leave us five star positive feedback.
Your affirmation is our greatest motivation ! !_x0000__x0000__x0000_