65W 204 control box 35000RPM 30V 210 102L Micromotor Handpiece Electric manicure machine Nail Drill Set

Read all instructions before using.（Please refer to the instruction manual）Thank you for your purchase！In order to have trouble-free performanceplease read all instructions before operating.is not responsible for the accident causing by not following the instructionsDesign and specification of the product can be subject to be changed for improving the quaity.Infoming the product, model, faulty status, and the customer (tel t or email etc), the kind consulting and quick service wil be provided.Handpiece -1 yearControl box & Foot Pedal-1 yearWarranty does not include misuse or nomal wear of bearing, carbon brush, collet chuck, ndle and armature.SERVICE FOR CHARGEIn case of the fault or malfunction from the misuse of the user-Using with wrong Input Voltage (AC Voltage)-Dropping down during setting or moving-In case of user's misuse or improper use-Using consumable parts or acceories not recommended by manufacturerOther cases-Faulty by Act of God (fire, sea wind or water, flood etc).Replacing by the normal wear of the consumable parts(ball bearings, collet chuck, carbon brush, ndle, or armatue etc.)SETING AND OPERATION1- Ar checking off-switch in control box, plug in.2- Connect handpiece to output of control box3- Set the speed dial of control box to "o".[caution!]in case of easy chuck change type or front-chuck-open type (Forte, 103L, 107 and 102WLHP),please use it ar checking the bur is completely lock. This is because the chuck could be loose ar chuck or bur change5- Hold handpiece with one hand and with the other hand, turn on the power of control box.6- Check handpiece running normally controlling speed dial in control box7- Tum off the power and connect the foot pedal to control box. Check speed operating of the pedal8- Turn off the power and switch to reverse direction. Turn on the power and check the operating.

Please tun off the switch when you do not use the unit.1 .Do not work in a dangerous place. Do not use the control box in a humid place.ac2 .Transport and storage conditions:Temperature: 10-40℃Humidity: 30-75% RHAtmospheric Preure:700 hPa to 1060 hPa3. Our handpiece & foot pedal should be only used for our confrol unit4.Bur*Dimensions of the bur. 2.35mm (SO7785-2 TYPE2)*Minimum iting length of bur of bur :10mm*When locked in the chuck, the maximum projection length of should be le than 35mm Use a bur that conform to the ISO standardsAvoid using a rusty or bent bur that may cause exceive wear of bearings.Keep safe speed, and precautions recommended by bur manufacturer5.Check for any troubles, inctuding vibration of bur,at low speed, and then start high speed6.Operate the speed control dial in control box softly7.use a fuse of 220V/230V/2A for control box(or110V）8.Turn off the power in order to change the bur.9.Be coreful not to drop the handpiece as it may be damaged or broken.in case that it is drooped, check if the bur is bent or if any exceive heat is generated while carefully operating it10.if ary problem occurs in handpiece, use ar repaining..11.Do not tumon the power of control box while the collet chuck of handpiece open (Short circuit of the motor may be coused)12 .Make sure that the switch is off before putting the power plug in the socket, in order to avoid on unexpected injury due to sudden start13.A circuit breaker is provided to protect the motor. it is actuated when there on overload which the motor cannot stand. Work within a range of load which it is not actuated14.Do not open the chuck while operating15.keep the handpiece with setting a bur to the collet chuck affer opperation16.Do not put the handpiece down befare it stops completely17.Besre to pul out the power cord before moving the control box18.use the specified voltage19.use acceories suitable for this product20.For recommended speed in various applications, follow the manufacture's instructions21.Wear proper profecive cothes and equipment ;including a dust mask and safety goles. Use a proper suction unit and a ventilator.22.keep the workplace clean. Debris may cause on accidentPackage Included:1 x control box1 x 102L Handpiece1 x Silicon Stand1x Foot Controller

1.pckages in 24 hours, but if the it are not in stock we have the ability to prepare the making in 2 days, and ship it within .2.Once you reiceive your products, remember to give a 5-star Feedback , you will be highly appreciated and you wilet god's bleing.3.If you couldn't receive your products or you don't like our it or our services, you don't need to open the dispute, just one meage, we will Solve any problem for you.Surely you will be happy to deal with us, don't you think so? ok, let's work togetherAgain and again.....

About shipping
Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days ar buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.