RGB MCU Adjustable Display Pattern 24 LED VU Level Indicator Meter Dual Channel

Product Description Video:

http://www.tudou.com/programs/view/RLesOyDUPTQ/

http://www.tudou.com/programs/view/ZN2LsxoeVJo/

This three color SMD LED, colorful, color flexible configuration, prefabricated a variety of color scheme, can set a color scheme specific to the color of each point, there are various design can choose, can adjust the brightne, the sensitivity adjustable, can set the infrared remote control self learning convenient control, infrared remote control need to match, only supports theN/E/C, this format is more common, can take home try television, set-top boxes, I get home in nine receiver remote control, remote control, haier TV Tmall magic box remote control and a waste of VCD remote control test can be used, remote control of home electric fans and air conditioning remote control test can't use). Size: length: 100 mm width :35 mm thickne :12.5 mm installed two hole center distance : 52 mm ,hole diameter: 3.2 mm (installation note mounting holes around the wiring insulation plus insulation gasket) Power supply: DC5v -6 v / 250 mA(Maximum current is LED the whole amount and the highest brightne, generally le than 100 mA) Audio signal: pick up the three lines on the headphone jack, respectively is a signal Ground (together with the power of the board negative) )left sound channel, right channel. Functional status and buttons operation: K1 and K2 two buttons, pre is have short pre and long pre . The following statement didn't explain the long pre is said short pre 1, level display status: according to the last time after the power supply power, the brightne of the former, figure, color scheme and sensitivity to normal level. This state the button function: K1 / show pattern selection click in a pattern, pattern at the end of the cycle from the very beginning. K1 long pre/to enter the pattern of color scheme selection state (note: the bottom upward emiion pattern buttons on long pre to enter the infrared learning state). K2 / sensitivity select click change sensitivity level, the order is the highest sensitivity.....The lowest sensitivity > > sensitivity automatically return to the highest sensitivity. K2 long pre/entered into a state of brightne adjustment. 2, Brightne adjustment status: the left section 24 of the bright display 8 red 8 green 8 blue, on the right shows the current brightne (red), 3 pieces according to grade 1, Toatl grade 8. This state the button functions: K1 / click the higher brightne level, the highest is all bright. K1 long pre/return level the brightne of the display status and return before entering the set. K2 / brightne click on the lower level, the lowest level is the low end of the three led light. K2 long pre/save the brightne of the set and returns the level display status. 3, color scheme selection state: left and right sides of each led all bright led displays the current color keep on top of the mode leds (peak said the color of the peak point). This state the button functions: K1 / click the show prefabricated color configuration scheme, the order is a scheme > > the current program, the last a prefabricated scheme > custom solutions (note that custom solutions when the factory is empty, that is, all black, the need to define the color of each dot) > prefabricated p 1, so cycle. K1 long pre/to save and select the current scheme return level display state. K2 / pre with K1 instead choose order. K2 long pre/to enter a custom color configuration status. 4, custom color configuration status: left and right side shows a custom color (not after custom shows full red) keep on top of the mode leds (peak said the color of the peak point) on the left side of the low end of the led flashing said the current led is selected. This state the button functions: K1 / click on the selected led moving up , the top the most low-end will move to another column. K1 long pre/color change to the next, change order red, yellow, green, blue, blue, magenta, six colors cycle show. K2 / click on the selected led moves down a, the bottom will be moved to another column led one of the most high-end. K2 long according to save the current color scheme and returns a color scheme selection state. 5, infrared learning key state: enter the state of all lights all out K1 and K2 button pre any returns level display status Need N/E/C of the infrared remote control (the remote control need since with) general TV set-top boxes, such as remote control can try sure no air conditioning, remote control or a lot of N/E/C format, is actually use the four buttons on the remote control to the corresponding board K1 short pre and pre K2 short pre and long according to the four functions. Since the learning proce: the first is the K1 short according to the corresponding function, with the remote control of the sensor of the board (without getting too close to) pre the button, if learn to work on the left will light up six led and into the K1 long according to the corresponding function learning state again pre the corresponding K1 long pre the remote control button again to add 6 led into the same proce in order to learn the K2 short pre and K2 long pre after the four keys will automatically save and return to the level display status at that time you can use the remote control to control, convenient try? If pre buttons have no reaction, estimation is infrared remote control code format is not suitable for, can only change the remote control to try again. Package include 100% 1pcs RGB MCU Adjustable Display Pattern 24 LED VU Level Indicator Meter Dual Channel About shipping
Shipping and Packaging All items will be double checked and well packed before sending.Items will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.